Job description of a flaw detection engineer. Flaw Detector Engineer Job Description Ultrasonic Testing Flaw Detector Job Description

Bogie frame, central beam, cardan coupling, automatic coupler parts, rail lubricator - magnetic particle control. 7. Welded seams of hull structures - ultrasonic testing. 8. Elements of wheelsets, inner and outer rings of roller bearings - magnetic and ultrasonic testing. Comments on the profession The given tariff and qualification characteristics of the profession ultrasonic control» serve for billing of works and assignment of tariff categories in accordance with article 143 Labor Code Russian Federation. Based on the above performance characteristics and requirements for professional knowledge and skills, a job description for a flaw detector operator for magnetic and ultrasonic testing is drawn up, as well as documents required for interviewing and testing when applying for a job.

Error 404 page does not exist

Connections of welded flanges, rings, intermediate fittings, nipples with pipes - magnetic particle inspection. 12. Units and parts of the helicopter are non-removable and easily accessible - magnetic particle inspection.

13. Welded seams of austenitic steels - registration of the distribution of the ferrite phase by the device. § 50. Defectoscopist for magnetic and ultrasonic testing (4th category) (introduced by Decree of the Ministry of Labor of the Russian Federation of 06/01/1998 N 20) Description of work.

Attention

Determining the quality of heat-treated parts and sorting them by material grades. Sorting of products by the amount of the ferrite phase. Measurement of the thickness of galvanized coatings.

Important

Construction of magnetization curves. Determination of magnetic permeability. Selection of the magnetization mode for eddy current testing of low-magnetic and magnetic products.

Magnetic and ultrasonic flaw detector

Per improper execution or failure to fulfill their official duties stipulated by this job description and the current labor legislation of the Russian Federation, abuse of the rights of a flaw detector operator for magnetic and ultrasonic testing of the 3rd category, or non-compliance with their duties. 4.2. For offenses committed in the course of carrying out their activities - within the limits determined by the current administrative, criminal and civil legislation of the Russian Federation.

4.3. For causing material damage - within the limits determined by the current labor and civil legislation of the Russian Federation. 5. WORKING CONDITIONS 5.1. The operating mode of the flaw detector operator for magnetic and ultrasonic testing of the 3rd category is determined in accordance with the Internal Labor Regulations established in the Organization.

5.2.

Job description of a flaw detection engineer

Info

Lviv10.01.2015 Job description No. 71 flaw inspector for magnetic and ultrasonic testing, Moscow 01.10.2015 1. MAIN PROVISIONS 1.1. This job description establishes the legal and production status, as well as the duties, rights and responsibilities of the flaw detector for magnetic and ultrasonic testing of JSC "Effect" (hereinafter referred to as the Company).

Job description of a flaw detector operator for magnetic and ultrasonic testing

The defectoscopist for magnetic and ultrasonic testing of the 6th category also bears other duties established by the local acts of the Organization. 2.3. . 3. RIGHTS The magnetic and ultrasonic inspection inspector of the 6th category has the right to: 3.1.
Request and receive the necessary materials and documents related to the activities of a flaw inspector for magnetic and ultrasonic testing of the 6th category. 3.2. Enter into relationships with departments of third-party institutions and organizations to resolve operational issues of production activities that are within the competence of the flaw detector operator for magnetic and ultrasonic testing of the 6th category. 3.3. Represent the interests of the enterprise in third-party organizations on issues related to its professional activities. 3.4. . 4.
This job description has been developed and approved in accordance with the provisions of the Labor Code of the Russian Federation; Unified Tariff and Qualification Handbook of Works and Professions of Workers, Issue 1, Professions of Workers Common to All Sectors of the National Economy, approved. Decree of the State Committee for Labor of the USSR and the Secretariat of the All-Union Central Council of Trade Unions of January 31, 1985 N 31 / 3-30; Model norms for the free issue of special clothing, special footwear and other personal protective equipment to employees of enterprises for the extraction and processing of uranium ores, for enrichment with uranium and its compounds, for the manufacture of fuel for nuclear reactors and for the production of electrical and thermal energy at nuclear power plants, employed at work with harmful and (or) hazardous conditions labor, as well as work performed in special temperature conditions or associated with pollution, approved.

Russian Federation; - basic requirements for the organization of labor; – internal labor regulations of the Company; – regulatory requirements for labor protection. 1.8. In order to implement the functions and exercise the rights set forth in this job description, the flaw detector for magnetic and ultrasonic testing interacts: - with the head of the quality control department or his substitute in terms of receiving instructions, instructions and other orders regulating his activities; – with other flaw detectorists on issues of working interaction.
2. RESPONSIBILITIES Flaw detector for magnetic and ultrasonic testing in the framework of his professional activities: 2.1. Determine the quality of heat-treated parts and sort them by material grade. 2.2. Performs sorting of products by the amount of the ferrite phase. 2.3.

Job description for ultrasonic testing flaw detector

Determination of the depth and size of defects in the root section of propeller blades. 3.7. Ultrasonic testing of plastics, rubber. 3.8. Ultrasonic testing of forgings various forms and sizes.

Ultrasonic testing of welded joints with wall thickness over 15 mm. 3.10. Measurement of the thickness of pipes made of corrosion-resistant steel with a wall thickness of more than 4 mm in the places of deflections.

Calibration of ballistic installations. 3.12. Magnetic control of the trunnion, axial joint housing, arm of the bushing blades rotor helicopter. 3.13. Magnetic and ultrasonic testing of wheel pair elements.

Rights A magnetic and ultrasonic inspection inspector of the 5th category has the right to: 4.1. For all statutory social guarantees.

4.2. Require the management of the enterprise to provide assistance in the performance of their professional duties and the exercise of rights. 4.3.
Ensures the safety of standards, tested measuring instruments, non-destructive testing tools at its disposal. 2.10. Carries out timely submission of instruments, measuring instruments for state verification, repair and their receipt. 2.11. Monitors the good condition and proper operation of non-destructive testing equipment, communications, production equipment and personal protective equipment. 2.12. Ensures the accuracy of the information provided. 2.13.

Mastering new technology and technological processes of control. 2.14. Observes the technological discipline of the control process.

2.15. Uses consumables sparingly. Timely acquaints laboratory assistants with the task and methods for its safe implementation, develops measures to ensure the safe performance of work. 2.16.
Average required professional education. Work examples. 1. Propeller shafts cylindrical hollow - ultrasonic testing. 2.

Propellers - ultrasonic testing of welds. 3. Inserts and pillows of bearings — ultrasonic control.

Boiler collector bottoms - ultrasonic testing. 5. Rolled square blanks - ultrasonic testing.

6. Propeller blades - determination of the depth and size of defects in the root section. 7. Plastics, rubber - ultrasonic testing. 8. Forgings of various shapes and sizes - ultrasonic testing. 9.

Welded joints with a wall thickness of more than 15 mm - ultrasonic testing. 10. Pipes made of corrosion-resistant steel with a wall thickness of more than 4 mm in the places of deflection - thickness measurement.

11. Ballistic installations - calibration. 12.
I approve [position, signature, full name of the manager or other official authorized to approve the job description] [date, month, year] L.P. developed and approved in accordance with the provisions of the Labor Code of the Russian Federation, the Unified Qualification Handbook for the Positions of Managers, Specialists and Employees, section " Qualification characteristics positions of employees of nuclear energy organizations”, approved. order of the Ministry of Health and social development of the Russian Federation of December 10, 2009 N 977, and other regulatory legal acts regulating labor relations. 1. General provisions 1.1. The flaw detection engineer belongs to the category of specialists and reports directly to [title of the position of the immediate supervisor]. 1.2.

SNiP, specifications, GOST, VSN, instructions, working drawings, PB and RD. 6.5. All LNC employees are responsible for: — violation of internal regulations; – disclosure of information constituting a trade secret and disclosure of restricted information; — non-compliance with a set of environmental measures; — non-compliance with technological discipline in production activities to reduce the harmful effects on the environment; — violation of labor protection requirements of industrial and fire safety, maintenance of equipment, tools, and office space in the wrong order; - obstruction of the activities of representatives of state supervision bodies. - ensure the reliability, objectivity and required accuracy of the results of control and bear full responsibility for them.

Job description of a flaw detection engineer

Interact with leaders structural services[enterprises, institutions, organizations], receive information and documents necessary for the performance of their official duties. 3.6. Correspond with organizations on issues within its competence. 3.7. Require management [of an enterprise, institution, organization] to assist in the performance of their duties and rights.
3.8. Improve your professional qualifications. 3.9. Other rights provided by labor legislation. 4. Responsibility The flaw detection engineer is responsible for: 4.1. For failure to perform or improper performance of their official duties provided for by this job description - within the limits determined by the current labor legislation of the Russian Federation; 4.2.

Error 404 page does not exist

Ensures the safety of standards, tested measuring instruments, non-destructive testing tools at its disposal. 2.10. Carries out timely submission of instruments, measuring instruments for state verification, repair and their receipt. 2.11. Monitors the good condition and proper operation of non-destructive testing equipment, communications, production equipment and personal protective equipment.

Attention

Ensures the accuracy of the information provided. 2.13. He masters new techniques and technological processes of control. 2.14. Observes the technological discipline of the control process.

Detector - who is it and what kind of profession?

Last edited by deniss; 06/20/2018 at 10:29 am. Kolyan2 Defectoscopist of all Russia Registration: 12/25/2012 Address: "Three screws" (Ufa, however ..) Posts: 3,199 Thanked: 829 times Thanked: 396 times Reputation: 377 Quote: Message from Deniss uh…well, yes…why won't it work?upd. Ah! is it in terms of the name? didn't even pay attention! so it was the Belarusian brothers who made up ...

they have a special language ... Normal language. I finally live in the Russian Republic of Belarus (Rep. Bashkortostan), so my lab was both indestructible and indestructible and I had a boss - labs of indestructible control! That's where the spissyfic is... Similar topics Technological cards and instructions for ultrasonic testing, MC, PVK Mardasov V Ultrasonic testing 7 08/29/2017 17:59 Job descriptions rus-ihm Radiographic testing 4 08/17/2017 11:43 Need instructions, NDT construction objects t1mur3 Documentation.

Non-destructive testing specialist (defectoscopist)

Important

Sorry, very sorry. And we have introduced positions and now instructions need to be written. Kolyan2 Detector of All Russia Registration: 12/25/2012 Address: "Three Screws" (Ufa, however ..) Posts: 3,199 Thanked: 829 times Thanked: 396 times Reputation: 377 Quote: Message from Lana -821 Sorry, really sorry. And we have introduced positions and now instructions need to be written.

Job description for ultrasonic testing flaw detector

Interact with the heads of structural services [enterprises, institutions, organizations], receive information and documents necessary for the performance of their duties. 3.6. Correspond with organizations on issues within its competence. 3.7. Require management [of an enterprise, institution, organization] to assist in the performance of their duties and rights. 3.8. Improve your professional qualifications. 3.9. Other rights provided by labor legislation. 4. Responsibility The flaw detection engineer is responsible for: 4.1. For failure to perform or improper performance of their official duties provided for by this job description - within the limits determined by the current labor legislation of the Russian Federation; 4.2.

Job description of a non-destructive testing laboratory flaw scopist

Participate in the discussion of the conditions of contacts that are directly related to the activities of the laboratory. 5.2.1. Use holding individual works flaw detection equipment, flaw detection materials, accessories and fixtures belonging to other organizations and individuals. 5.2.2. Require the "Customer" and "Contractor" to perform work in strict accordance with the NTD, technical regulations and design solutions.
5.2.3. Make comments and instructions in the work logs of the “Construction Object” under construction in accordance with the “Regulatory Documentation” and “ technical regulations". 5.2.4. Inform the supervisory authorities about the negative results of work carried out by contractors. 5.2.5.
To perform functions and exercise rights, LNC interacts with departments, services, organizations, while the rights and obligations of the parties in relation to each other are determined by the current legislation, the provisions governing the activities of the parties, the requirements of the NTD. 7.2. third parties for the NDT laboratory may be: bodies of Rostekhnadzor of Russia; bodies that carry out verification of measuring instruments, interaction is carried out in accordance with the Law of the Russian Federation. Customers - consumers of laboratory services, suppliers of products and services necessary to ensure the functioning of the laboratory.

Performs visual and measuring control welded joints, diagnostics of shut-off and distribution valves. 4.2. Provides quality control of welded joints of main, technological oil pipelines, gas pipelines, Equipment of oil pumping stations (OPS). — visual and measuring method of control; — X-ray control; — ultrasonic control; — magnetic particle testing — capillary method (color) — eddy current testing — electric testing 4.3. Development of technological documentation and projects of changes to them related to the adjustment of technological processes.
4.4. Participation in industrial testing of new types of machines, mechanisms, means of automation and mechanization of production. 5. Rights and obligations 5.1. Refuse to work (order), the conditions, the fulfillment of which may affect the objectivity of the control results. 5.2.

GOSTs 0 06/22/2015 16:51 Need instructions for certification of the NK laboratory bobov Documentation. GOSTs 2 13.02.2015 10:51 Help me find safety instructions for VC, UT, MPD bondary05 Documentation. GOSTs 0 15.04.2013 16:21 « Previous topic | Next Topic » You can't post new topics You can't reply to topics You can't attach attachments You can't edit your posts BB codes Incl.

Smilies On code on HTML Code Off Forum rules Quick navigationMy accountPersonal messagesSubscriptionsWho is on the forumSearch forumForum home pageForum Fault scopist Ultrasonic testing Radiographic testing Capillary testing Magnetic particle testing Defectoscopy on railway Energy audit and temperature control Eddy current control Visual and measurement control Acoustic emission General issues Articles about defectoscopy Documentation.

This job description was developed and approved in accordance with the provisions of the Labor Code of the Russian Federation, the Unified Tariff and Qualification Reference Book of Works and Professions of Workers, Issue 1, Professions of Workers Common to All Sectors of the National Economy, approved. Decree of the State Committee for Labor of the USSR and the Secretariat of the All-Union Central Council of Trade Unions of January 31, 1985 N 31 / 3-30; Model norms for the free issuance of special clothing, special footwear and other personal protective equipment to workers in chemical industries engaged in work with harmful and (or) dangerous working conditions, as well as in work performed in special temperature conditions or associated with pollution, approved. by order of the Ministry of Health and Social Development of the Russian Federation of August 11, 2011 N 906n, and other regulatory legal acts regulating labor relations.

1. General Provisions

1.1. An X-ray, gamma-ray flaw detector of the 5th category belongs to the category of workers and directly reports to [position title of immediate supervisor].

1.2. For the position of an X-ray, gamma-ray flaw detector of the 5th category, a person is accepted without presenting requirements for education, who has work experience in the specialty [insert as appropriate].

1.3. An X-ray, gamma-ray flaw detector of the 5th category is accepted and dismissed from work by order [the position of the head of the organization].

1.4. The defectoscopist of X-ray, gamma graphy of the 5th category must know:

— the principle of operation of X-ray installations of accelerator technology, equipment for gamma-graphy, ionization and scintillation control;

— types and sources of radiation and their nature;

- the passage of radiation through substances;

- properties of different grades of X-ray films and methods for checking their quality;

— methods of charging cassettes;

— fundamentals of electrical engineering and metallurgy;

– casting technology and various kinds metal welding;

— types of welded joints and technology of their welding;

— the effect of defects on the quality of welds;

— requirements for welds;

— basics of dosimetry;

— attenuating properties of materials when radiation passes through them;

- properties and characteristics of metals used for x-ray, gamma graphy;

- methods for choosing radiation sources, transmission parameters and necessary exposures;

- electrical circuits of x-ray, radiographic equipment for ionization and scintillation control;

— interaction of high-energy radiation with a translucent substance; fundamentals of xerography;

—calculation of permissible radiation doses, distances from sources and residence time at given distances from sources;

- basic information about the design of various accelerators;

- schemes and operation of all equipment used for transmission control, principles for obtaining various types of radiation and their interaction with a translucent substance;

— calculation of radiation protection;

— the procedure for obtaining and storing radioactive sources operating at the enterprise;

— rules and regulations on labor protection, industrial sanitation and fire safety;

- rules for the use of personal protective equipment;

- requirements for the quality of work performed;

- types of marriage and ways to prevent and eliminate it;

- industrial signaling;

— requirements for rational organization labor in the workplace.

2. Job responsibilities

2.1. Transillumination of products of complex configuration using stationary and mobile radiation sources.

2.2. Ionization and scintillation control of complex products.

2.3. Illumination of critical pipelines.

2.4. Transillumination of products using accelerator technology and gamma-ray installations.

2.5 Preparation of products for transillumination.

2.6. Marking and marking of areas during the translucence of products according to the specified control parameters.

2.7. Developing and fixing x-ray film.

2.8. Selection of necessary radiation sources and determination of exposure.

2.9. Determination of the activity of a radioactive isotope.

2.10. View pictures to determine their quality.

2.11. Regulation of X-ray and gamma-graphic equipment.

2.12. Work on xerographic installations.

2.13. Work on X-ray television installations.

2.14. Current repair and adjustment of x-ray and radiographic equipment.

2.15. Charging and recharging radiation sources.

2.16. Interpretation of radiographs.

2.17. Adjustment of equipment used for X-ray, gamma-defectoscopy, ionization and scintillation control.

2.18. Evaluation of the suitability of tested samples, parts and assemblies in accordance with the technical specifications and issuance of conclusions.

2.19. Development of sketches of devices and equipment for control.

3. Types of work

X-ray and gamma-graphy flaw detector of the 5th category performs the following types of work:

3.1. Transmission of samples of plates during certification for the category of welders.

3.2. Illumination of butt joints.

3.3. Transillumination of seams of longitudinal cylinders and conical shells.

3.4. Illumination of cast products.

3.5. Transillumination of tee and strip-bulb joints

3.6. Illumination of welded pipes.

3.7. Translucence of the pipe, bushings of the main rotor of the helicopter.

3.8. Transillumination of the seams of annular cylinders and cylinders.

3.9. Transmission of welds in cylindrical and spherical surfaces.

3.10. Transmission and interpretation of radiographs of the fuel manifold of an aircraft engine.

3.11. Transmission and interpretation of radiographs of propellers.

3.12. Transmission and interpretation of radiographs of automation units and nozzles of gas turbine engines.

3.13. Transmission and interpretation of radiographs of the helicopter swash plate.

3.14. Chassis shock absorber struts Chassis shock absorber struts.

3.15. Reloading work containers with isotopes.

3.16. Translucence of metal and charge for metallurgical shops.

3.17. Transillumination of welded seams of casings of mines and air heaters of blast furnaces.

3.18. Transillumination of welded seams of pipelines and gas pipelines.

4. Rights

X-ray, gamma-graphy flaw detector of the 5th category has the right to:

4.1. For all social guarantees provided for by law.

4.2. Require the management of the enterprise to provide assistance in the performance of their professional duties and the exercise of rights.

4.3. Require the creation of conditions for the performance of professional duties, including the provision of necessary equipment, inventory, workplace that meets sanitary and hygienic rules and regulations, etc.

4.4. To receive special clothing, special footwear and other personal protective equipment.

4.5. Payment of additional expenses for medical, social and professional rehabilitation in cases of damage to health due to an accident at work and occupational disease.

4.6. Get acquainted with the draft decisions of the management of the enterprise relating to its activities.

4.7. Submit proposals for the management of the enterprise to improve the organization and improve the methods of work performed by it.

4.8. Request personally or on behalf of the immediate supervisor documents, materials, tools, etc., necessary for the performance of their duties.

4.9. Improve your professional qualifications.

4.10. [Other rights under labor law].

5. Responsibility

The X-ray, gamma-ray flaw detector of the 5th category is responsible for:

5.1. For failure to perform or improper performance of their official duties provided for by this job description - within the limits determined by the current labor legislation of the Russian Federation;

5.2. For causing material damage to the employer - within the limits determined by the current labor and civil legislation of the Russian Federation;

5.3. For offenses committed in the course of carrying out their activities - within the limits determined by the current administrative, criminal, civil legislation of the Russian Federation.

The job description was developed in accordance with [name, number and date of the document]

Head of Human Resources

[initials, last name]

[signature]

[day month Year]

Agreed:

[position]

[initials, last name]

[signature]

[day month Year]

Familiarized with the instructions:

[initials, last name]

[signature]

[day month Year]

Job description of a flaw scopist for x-ray, gamma graphy of the 5th category

Job description
flaw detection engineer[name of organization, enterprise, etc.]

This job description was developed and approved in accordance with the provisions of the Labor Code of the Russian Federation, the Unified Qualification Handbook for the Positions of Managers, Specialists and Employees, section "Qualification Characteristics of Positions of Employees of Nuclear Energy Organizations", approved. by order of the Ministry of Health and Social Development of the Russian Federation of December 10, 2009 N 977, and other regulatory legal acts regulating labor relations.

1. General Provisions

1.1. The flaw detection engineer belongs to the category of specialists and reports directly to [title of the position of the immediate supervisor].

1.2. A person who has a higher professional (technical) education without presenting requirements for work experience or a secondary professional (technical) education and at least 3 years of work experience as a technician of category I for at least 3 years or in other positions filled by specialists with secondary professional (technical) education, at least 5 years.

1.3. The flaw detection engineer must know:

Laws and other regulations legal acts Russian Federation, methodological and regulatory documents regulating the production, economic and financial and economic activities of the organization;

Prospects for the development of the organization;

Regulatory and methodological documents of the system of labor safety standards and state system measurements;

Design features of the control object, types of defects to be detected, their potential danger;

Instructions for secret office work;

Non-destructive testing methodology, normative and technical documentation for non-destructive testing;

Rules for selection and quality control of applied flaw detection materials;

Types of defects, their classification, identification features of detected defects, their division into classes and types;

Harmful production factors of this control method and methods of protection against their impact;

Requirements normative documents on civil defense and emergency situations;

Fundamentals of economics, organization of production, labor and management;

Basics of labor legislation;

Rules for environmental protection, nuclear and radiation safety;

Rules on labor protection and fire safety;

Internal labor regulations;

Rules and norms of labor protection.

2. Job responsibilities

Fault Detector Engineer:

2.1. Carries out work on non-destructive testing and diagnostics of products in the organization.

2.2. Plans and monitors the quality of work based on repair schedules, requests from the organization, contracts, work plans.

2.3. Gives tasks to laboratory assistants with an entry in the task log.

2.4. Monitors compliance with the deadlines for briefing laboratory assistants.

2.5. Monitors the quality of non-destructive testing performed by subordinate employees.

2.6. Gives conclusions about the quality of control objects, controlled independently or by laboratory assistants, with inspection control, if necessary.

2.7. Maintains operational records of measuring instruments, instruments, their movement.

2.8. Calculates the needs of the unit in measuring instruments, instruments, draws up applications for their purchase.

2.9. Ensures the safety of standards, tested measuring instruments, non-destructive testing tools at its disposal.

2.10. Carries out timely submission of instruments, measuring instruments for state verification, repair and their receipt.

2.11. Monitors the good condition and proper operation of non-destructive testing equipment, communications, production equipment and personal protective equipment.

2.12. Ensures the accuracy of the information provided.

2.13. He masters new techniques and technological processes of control.

2.14. Observes the technological discipline of the control process.

2.15. Uses consumables sparingly. Timely acquaints laboratory assistants with the task and methods for its safe implementation, develops measures to ensure the safe performance of work.

2.16. Monitors the condition of the used protective equipment, safety devices, devices and fences.

2.17. Controls the compliance of subordinate employees with the rules on labor protection, nuclear, radiation and fire safety, the requirements of the secrecy regime, the preservation of official, commercial and state secrets, and non-disclosure of confidential information.

3. Rights

The flaw detection engineer has the right to:

3.1. For all social guarantees provided for by law.

3.2. Get acquainted with the draft decisions of the management [of the enterprise, institution, organization] relating to its activities.

3.3. Submit proposals for improvement of the work related to the responsibilities provided for in this instruction for consideration by the management.

3.4. Sign and endorse documents within their competence.

3.5. Interact with the heads of structural services [enterprises, institutions, organizations], receive information and documents necessary for the performance of their duties.

3.6. Correspond with organizations on issues within its competence.

3.7. Require management [of an enterprise, institution, organization] to assist in the performance of their duties and rights.

3.8. Improve your professional qualifications.

3.9. Other rights provided by labor legislation.

4. Responsibility

The inspection engineer is responsible for:

4.1. For failure to perform or improper performance of their official duties provided for by this job description - within the limits determined by the current labor legislation of the Russian Federation;

4.2. For causing material damage to the employer - within the limits determined by the current labor and civil legislation of the Russian Federation;

4.3. For offenses committed in the course of carrying out their activities - within the limits determined by the current administrative, criminal, civil legislation of the Russian Federation.

The job description was developed in accordance with [name, number and date of the document]

Head of Human Resources

[initials, last name]

[signature]

[day month Year]

Agreed:

[position]

[initials, last name]

[signature]

[day month Year]

Familiarized with the instructions:

[initials, last name]

[signature]

[day month Year]

Determination of the depth and size of defects in the root section of propeller blades. 3.7. Ultrasonic testing of plastics, rubber. 3.8. Ultrasonic testing of forgings of various shapes and sizes. 3.9. Ultrasonic testing of welded joints with wall thickness over 15 mm. 3.10. Measurement of the thickness of pipes made of corrosion-resistant steel with a wall thickness of more than 4 mm in the places of deflections. 3.11. Calibration of ballistic installations. 3.12. Magnetic control of the trunnion, the axial hinge housing, the arm of the blades of the main rotor hub of the helicopter. 3.13. Magnetic and ultrasonic testing of wheel pair elements. 4. Rights A magnetic and ultrasonic inspection inspector of the 5th category has the right to: 4.1. For all social guarantees provided for by law. 4.2. Require the management of the enterprise to provide assistance in the performance of their professional duties and the exercise of rights. 4.3.

Anna Serebryova

Russian Federation; - basic requirements for the organization of labor; – internal labor regulations of the Company; – regulatory requirements for labor protection. 1.8. In order to implement the functions and exercise the rights set forth in this job description, the flaw detector for magnetic and ultrasonic testing interacts: - with the head of the quality control department or his substitute in terms of receiving instructions, instructions and other orders regulating his activities; – with other flaw detectorists on issues of working interaction. 2. RESPONSIBILITIES Flaw detector for magnetic and ultrasonic testing in the framework of his professional activities: 2.1.

Determine the quality of heat-treated parts and sort them by material grade. 2.2. Performs sorting of products by the amount of the ferrite phase. 2.3.

Job description of a flaw detection engineer

Guiding documents, on the provisions of which the flaw detector for magnetic and ultrasonic testing should rely in their activities, are: the Constitution of the Russian Federation, the Labor Code of the Russian Federation, GOSTs, SNiPs and guidelines in the field of magnetic and ultrasonic testing, the Charter of the Company, orders and orders of the General Director of the Company, this job description and other local regulations of the Company. 1.6. The position of a flaw detector for magnetic and ultrasonic testing is entitled to be occupied by a person with a specialized secondary vocational education, with experience in the specialty for at least one year. 1.7.

Job description of a flaw detector operator for magnetic and ultrasonic testing

Attention

Interact with the heads of structural services [enterprises, institutions, organizations], receive information and documents necessary for the performance of their duties. 3.6. Correspond with organizations on issues within its competence. 3.7. Require management [of an enterprise, institution, organization] to assist in the performance of their duties and rights.

Error 404 page does not exist

Important

The Job Description section contains the necessary information on how a job description is written. Here you can find typical job descriptions for various specialties. Our bank of job descriptions includes more than 2500 different documents.

• what duties, powers and rights are reflected in the job description of a flaw detector operator for magnetic and ultrasonic testing;
• what provisions are contained in the standard job description of a flaw detector operator for magnetic and ultrasonic testing;
• what areas of work under this job description is the responsibility of this specialist in your organization.

Society with limited liability Alfa APPROVEDGeneral Director A.V.
The responsibility of the flaw detector for magnetic and ultrasonic testing for causing material damage to the employer occurs in the manner and on the conditions determined by the labor legislation of the Russian Federation. 4.4. For disciplinary, civil, administrative and criminal violations of the law, the flaw detector for magnetic and ultrasonic testing is liable under the relevant regulations. 4.5. For non-observance of the confidentiality of information and failure to ensure the safety of documents, access to which the flaw detector for magnetic and ultrasonic testing has for official purposes, he bears the responsibility provided for by law.
4.6.
Job description for a flaw detection engineer [name of organization, enterprise, etc.] This job description was developed and approved in accordance with the provisions of the Labor Code of the Russian Federation, the Unified Qualification Handbook for the Positions of Managers, Specialists and Employees, section "Qualification characteristics of positions of employees of nuclear energy organizations" , approved by order of the Ministry of Health and Social Development of the Russian Federation of December 10, 2009 N 977, and other regulatory legal acts regulating labor relations.1. General provisions 1.1. The flaw detection engineer belongs to the category of specialists and reports directly to [title of the position of the immediate supervisor]. 1.2.
Seek assistance from other employees of the quality control group, as well as from the management of the Company. 3.4. Require compliance with his rights established by this job description. 3.5. Receive for review documents establishing, changing or canceling his official rights and obligations.

3.6.

Demand the provision of working conditions that meet established standards. 3.7. Submit proposals to improve the efficiency of the organization and work performance for consideration by the Company's management. 3.8. Take a course professional retraining in accordance with the established procedure.

4. RESPONSIBILITY 4.1.

Flaw Detector Engineer qualification guide positions of managers, specialists and other employees (CEN), 2017 Section "Qualification characteristics of positions of employees of nuclear energy organizations" Section approved by Order of the Ministry of Health and Social Development of the Russian Federation dated December 10, 2009 N 977 Engineer of the gas rescue service Table of contents Engineer-dosimetrist Job Responsibilities. Carries out work on non-destructive testing and diagnostics of products in the organization. Plans and monitors the quality of work based on repair schedules, requests from the organization, contracts, work plans.

Gives tasks to laboratory assistants with an entry in the task log. Flaw detectorist for ultrasonic non-destructive testing (UK) Ensures the safety of standards, tested measuring instruments, non-destructive testing tools at his disposal. 2.10.
Demand the creation of conditions for the performance of professional duties, including the provision of the necessary equipment, inventory, a workplace that meets sanitary and hygienic rules and regulations, etc. 4.4. To receive special clothing, special footwear and other personal protective equipment. 4.5. Payment of additional expenses for medical, social and professional rehabilitation in cases of damage to health due to an accident at work and occupational disease.
4.6.

Get acquainted with the draft decisions of the management of the enterprise relating to its activities. 4.7. Submit proposals for the management of the enterprise to improve the organization and improve the methods of work performed by it. 4.8. Request personally or on behalf of the immediate supervisor documents, materials, tools, etc.