Job responsibilities of an electrician. Job responsibilities of the electrician Description of work, tasks and job responsibilities

\Typical job description of an electrician-electrician of the 3rd category

Job description of a fitter-electrician of the 3rd category

Position: Electrical fitter of the 3rd category
Subdivision: _________________________

1. General Provisions:

    Subordination:
  • Electrical fitter of the 3rd category is directly subordinate to ........................
  • Electrical fitter of the 3rd category follows the instructions ......................................... ...........

    • (the instructions of these workers are carried out only if they do not contradict the instructions of the immediate supervisor).

    Substitution:

  • A fitter-electrician of the 3rd category replaces .......................................... .......................................
  • A fitter-electrician of the 3rd category is replaced by .......................................... .....................................

    • Reception and dismissal:
    An electrical fitter is appointed and dismissed by the head of the department in agreement with the head of the department.

2. Qualification requirements:
    Must know:
  • fundamentals of electrical engineering in the amount of work performed
  • device and principle of operation of DC and AC machines with power over 50 to 100 kW
  • ballasts of medium complexity
  • permissible loads during operation of electric machines
  • ways of adjusting the brush mechanism of the electric motor
  • method of processing winding-sealing materials (impregnation, lubrication, welding, braiding, etc.)
  • system of tolerances and landings
  • device and purpose of control and measuring and installation tools, special devices and equipment used in electrical installation
  • technical conditions for testing electrical equipment
  • diagrams of assembled and assembled devices, devices and electric cranes with control.
3. Job responsibilities:
  • Installation, assembly, testing and delivery of electrical machines of direct and alternating current with a capacity of over 50 to 100 kW, electrical appliances of medium complexity and units for them using universal devices.
  • Assembly and installation of complex electrical appliances and electrical machines using special tools and templates.
  • Detection during installation of damages in electrical equipment and their elimination.
  • Installation and installation of switchboards for more than eight groups and busbar assemblies, as well as electrical equipment for cranes with a lifting capacity of up to 20 tons, welding machines with a capacity of over 300 kW and mercury rectifiers with a capacity of up to 500 kW.
  • Binding of electrical circuits from conductors of various cross-sections and complete installation in housings.
  • Work on switching switchboards for power electrical installations.
  • Installation of equipment and complete switching of power stations for amperage up to 1000 A.
  • Feeder and distribution network laying.
  • Assembly and installation of complex electrical equipment and products under the guidance of a highly qualified electrician.
page 1 Job description Electrical fitter
page 2 Job description Electrical fitter

4. Rights

  • The fitter-electrician has the right to give orders to subordinate employees, assignments on a range of issues included in his functional duties.
  • The fitter-electrician has the right to control the execution of production tasks, the timely execution of individual orders by the employees subordinate to him.
  • The fitter-electrician has the right to request and receive the necessary materials and documents related to the issues of his activities and the activities of employees subordinate to him.
  • The fitter-electrician has the right to interact with other services of the enterprise on production and other issues that are part of his functional duties.
  • The fitter-electrician has the right to get acquainted with the draft decisions of the management of the enterprise concerning the activities of the Division.
  • The fitter-electrician has the right to propose for the manager's consideration proposals for improving the work related to the duties provided for in this Job Description.
  • The fitter-electrician has the right to submit to the manager for consideration proposals on the encouragement of distinguished workers, the imposition of penalties on violators of production and labor discipline.
  • The fitter-electrician has the right to report to the head about all violations and shortcomings in connection with the work performed.
5. Responsibility
  • The fitter-electrician is responsible for improper performance or non-performance of his duties, provided for by this job description - within the limits determined by the labor legislation of the Russian Federation.
  • The electrician is responsible for violation of the rules and regulations governing the activities of the enterprise.
  • When transferring to another job or dismissal, the Electrical Fitter is responsible for the proper and timely delivery of cases to the person taking the current position, and in the absence of such, to the person replacing him or directly to his manager.
  • The electrician is responsible for offenses committed in the course of carrying out his activities - within the limits determined by the current administrative, criminal and civil legislation of the Russian Federation.
  • The fitter-electrician is responsible for causing material damage - within the limits determined by the current labor and civil legislation of the Russian Federation.
  • The fitter-electrician is responsible for compliance with the current instructions, orders and orders for the preservation of trade secrets and confidential information.
  • The electrician is responsible for compliance with internal regulations, safety and fire safety rules.
This job description was developed in accordance with (name, number and date of the document)

Head of structural

In accordance with the main tasks assigned to the power supply service, an electrician for the repair and maintenance of electrical equipment is obliged to:

1. Perform daily inspections of the fixed equipment with an entry in the operational log;

2. Take measures to eliminate the identified comments yourself, and if it is impossible to report this to the EMU engineer, the shift engineer of the compressor station;

3. Perform operational switching in electrical installations up to and above 1000V;

4. Prepare workplaces and carry out the admission of repair crews.

5. Perform maintenance and repair work on electrical equipment.

6. Have permission to perform hot work, work from an assembly tower, sling work, gas hazardous work, work at height.

7. Rational use of material resources, consumption of fuel, energy, raw materials and materials when performing work.

8. Observe the technological process of the work performed, the rules of technical operation and maintenance of equipment, devices and tools.

9. Know the requirements for the quality of work performed.

10. Ensure a rational organization of work in your workplace

11. In the absence of the work stipulated in the production instructions, the head of the EMU (EMU engineer) has the right to assign temporarily to perform any other work that does not require special training and higher qualifications.

Obligations for labor protection and industrial safety.

Is responsible for compliance with the requirements of labor protection instructions by type of work and by profession.

Participates in the first level of control over the state of labor protection, before the start of the shift (working day) inspects the workplace.

Monitors the serviceability of equipment, fixtures, tools and devices.

Checks the presence and serviceability of fences, safety devices, interlocking and signaling devices, individual and group protection equipment, the condition of walkways, crossings, platforms, staircases, railings, as well as the absence of their clutter and clutter.

It reports to the foreman (foreman) about the deficiencies found during the inspection and, on his instructions, participates in their elimination.

In the process of work, the employee is obliged:

use overalls and other protective equipment, use safe working practices, while observing all labor protection requirements;

pay attention to the behavior of other employees, their implementation of personal safety measures, remind them of the need to use safe working practices, comply with safety requirements, industrial sanitation, fire and gas safety;

undergo training in safe methods and techniques for performing work, instructing on labor protection, internship at the workplace and testing knowledge of labor protection requirements;

undergo mandatory preliminary (upon admission to work) and periodic (during employment) medical examinations (examinations).

The employee is responsible for:

technically sound condition of equipment, mechanisms in terms of compliance of actual harmful emissions / discharges with the passport data of this mechanism;

timely submission of equipment, mechanisms for instrumental measurement of the amount of harmful emissions / discharges;

timely and high-quality accounting of operating hours of equipment that are sources of harmful emissions / discharges.

For violation of environmental protection, the employee bears disciplinary, administrative or criminal, as well as material liability.

Description of the work.

Performing simple work on departmental e-mail. stations, transformer power plants with their complete disconnection from the voltage of operational switching in power grids, revision of transformers, switches, disconnectors and drives to them without disassembling structural elements.

Load regulation of electrical equipment installed in the serviced area.

Repair, charging and installation of explosion-proof valves.

Cutting, splicing, insulation and soldering of wires with voltage over 1000 V.

Participation in the repair, inspection and maintenance of electrical equipment with the performance of work on disassembly, assembly, adjustment and maintenance of electrical devices, electromagnetic, magnetoelectric and electrodynamic systems.

Repair of transformers, switches, rheostats, control stations of magnetic starters, contactors and other simple equipment.

Performing individual complex repairs under the guidance of e-mail. fitters of higher qualifications.

Rigging operations using cranes and other lifting machines

Participation in the laying of cable routes and wiring

Battery charge

Painting of external parts of devices and equipment.

Reconstruction of email equipment

Processing according to the drawing of insulating materials: textolite, getinax, fiber, etc.

Checking the marking of simple installation and circuit diagrams.

Identification and elimination of failures, malfunctions and damage to electrical equipment with simple switching schemes.

The employee must know:

Fundamentals of Electrical Engineering.

Information about direct and alternating current in the amount of work performed.

The principle of operation and design of serviced electric motors, generators, switchgear equipment, power grids and electrical appliances, oil switches, fuses, contactors, batteries, controllers, mercury and silicon rectifiers and other electrical equipment and electrical appliances

Design and purpose of starting and regulating devices

Techniques and methods, replacement, splicing and soldering of high voltage devices.

Safe work practices, sequence of disassembly, repair and installation of electrical equipment.

Designations of the conclusions of the windings of electrical machines.

Solders and fluxes.

Conducting and electrical insulating materials and their main characteristics and qualifications

The device and purpose of a simple and medium complexity of control and measuring tools and devices.

Methods for measuring electrical quantities, methods for finding and eliminating faults in power grids.

Rules for laying cables indoors, underground and on overhead cables.

Safety regulations in the scope of the qualification group

Description of the work.

Performing simple work at departmental power plants; transformer power substations with their complete disconnection from the voltage of operational switching in power grids, revision of transformers, switches, disconnectors and drives to them without disassembling structural elements. Regulation of the load of electrical equipment installed in the serviced area. Repair, charging and installation of explosion-proof valves. Cutting, splicing, insulation and soldering of wires with voltage over 1000 V. Maintenance and repair of solar and wind power plants with a capacity of over 50 kW. Participation in the repair, inspection and maintenance of electrical equipment with the performance of work on disassembly, assembly, adjustment and maintenance of electrical devices, electromagnetic, magnetoelectric and electrodynamic systems. Repair of transformers, switches, rheostats, control posts, magnetic starters, contactors and other simple equipment. Performing individual complex repairs under the guidance of highly qualified electricians. Rigging operations using cranes and other lifting machines. Participation in the laying of cable routes and wiring. Battery charge. Painting of external parts of devices and equipment. Reconstruction of electrical equipment. Processing according to the drawing of insulating materials: textolite, getinax, fiber, etc. Checking the marking of simple installation and circuit diagrams. Identification and elimination of failures, malfunctions and damage to electrical equipment with simple switching schemes.

Must know:

Fundamentals of Electrical Engineering; information about direct and alternating current in the amount of work performed; the principle of operation and design of serviced electric motors, generators, switchgear equipment, power grids and electrical appliances, oil switches, fuses, contactors, batteries, controllers, mercury and silicon rectifiers and other electrical equipment and electrical appliances; design and purpose of starting and regulating devices; techniques and methods for replacing, splicing and soldering high voltage wires; safe work practices, the sequence of disassembly, repair and installation of electrical equipment; designation of the conclusions of the windings of electrical machines; solders and fluxes; conductive and electrical insulating materials, their main characteristics and classification; the device and purpose of a simple and medium complexity of control and measuring tools and devices; methods of measuring electrical quantities; techniques for finding and eliminating faults in power grids; rules for laying cables indoors, underground and on overhead cables; safety regulations in the scope of qualification group 3.

Work examples:

  • 1. Ammeters and voltmeters of electromagnetic and magnetoelectric systems - check in special conditions.
  • 2. Controlling equipment: rheostats, magnetic starters, starter boxes, etc. - disassembly, repair and assembly with cleaning burnt contacts, brushes or changing them.
  • 3. Equipment starting up magnetic stations of rolling mills - disassembly, repair and assembly.
  • 4. Devices brake and limit switches - repair and installation.
  • 5. Funnels, end couplings - cutting and mounting on the cable.
  • 6. Selenium rectifiers - check and repair.
  • 7. Garlands of electric lamps - production with parallel and series connection.
  • 8. Details of complex configuration for electrical equipment: clamps, switches, fingers and resistance boxes - manufacturing.
  • 9. Cables - checking the insulation condition with a megohmmeter.
  • 10. Rig Control Station Controllers - Inspection, Repair, Assembly and Installation.
  • 11. Portal cranes, container cranes - disassembly, repair, assembly of contactors, controllers, relays, knife switches, switches.
  • 12. Special loaders, hold, fork and storage vehicles - disassembly, repair and assembly of controllers, contactors, switches, starting resistors, lighting and signaling devices.
  • 13. Plain bearings of electric motors - change, filling.
  • 14. Electronic potentiometers for automatic temperature control of calcining furnaces and drying equipment - installation, repair and replacement.
  • 15. Devices for automatic measurement of temperature and pressure - elimination of simple malfunctions, replacement of sensors.
  • 16. Power supply cables - lead to the machine in the gas pipe.
  • 17. Intermediate automatic regulator relay - check and replace.
  • 18. Light advertising - installation.
  • 19. Switch, disconnectors - regulation of contacts for simultaneous switching on and off.
  • 20. Centrifuge - revision with plate cleaning.
  • 21. Boards of a power or lighting network with a complex circuit (more than eight groups) - manufacturing and installation.
  • 22. Asynchronous electric motors with phase rotor power up to 500 kW - disassembly and assembly.
  • 23. Short-circuited electric motors up to 1000 kW - disassembly and assembly.
  • 24. Explosion-proof electric motors with power up to 50 kW - disassembly, repair and assembly.
  • 25. Power tools - disassembly, repair and assembly.
  • 26. Anchors, magnetic coils, brush holders of electric machines - repair and replacement.

Unified tariff and qualification reference book of jobs and professions of workers (ETKS), 2019
Part No. 2 of issue No. 2 ETKS
The issue was approved by the Resolution of the Ministry of Labor of the Russian Federation of 11/15/1999 N 45
(as amended by the Order of the Ministry of Health and Social Development of the Russian Federation of 13.11.2008 N 645)

Electrical fitter

§ 172. Electrician-electrician of the 2nd category

Description of works... Assembly of simple assemblies and devices using universal devices and tools. Installation and installation of AC and DC electrical machines with a power of up to 50 kW and welding machines with a power of up to 30 kW. Testing of mounted machines and equipment after installation. Assembly and installation of medium complexity components and equipment using special tools and templates. Manufacturing of parts, assembly of fixtures and templates. Manufacturing of parts, assembly, testing and installation of simple electrical structures of low-voltage equipment, as well as electrical appliances and control gear. Installation and soldering of conductor lugs. Coloring of conductors in the set colors. Assembly and installation of lighting panels for up to eight groups of couplings, tees and boxes. Assembling wires of simple circuits. Panel preparation, installation of communication equipment and installation of a power station. Laying of light, power and signaling networks. Punching holes in brick and concrete walls with bolts and pneumatic tools. Drilling, reaming, manual and machine tapping. Tinned cable ends. Assembly, installation and testing of more complex products and electrical machines under the guidance of a highly qualified electrician.

Must know: fundamentals of electrical engineering in the amount of work performed; device and principle of operation of simple electrical machines with a power of up to 50 kW, instruments, starting equipment and technical conditions for their installation; methods of work with pneumatic and electric drills and drilling machines; the purpose of the materials used in the work; solder and fluxes used in soldering, and soldering rules; methods of laying wires in gas pipes, on rollers and cable hangers; rules for switching on electrical machines; locksmith and control and measuring tools, fixtures and equipment used during assembly and installation.

Work examples

1. Ammeters, voltmeters, electricity meters - plugging into the network.

2. Lighting switches - installation.

3. Plug sockets - panel assembly and installation.

4. Details of control gear - manufacturing.

5. Insulation boards for power and lighting shields - manufacturing.

6. Electromagnetic coils for devices of different types and systems - winding and installation in place.

7. Dynamos and motors collectors - cleaning during assembly.

8. Table lamps - assembly.

9. Contact petals - riveting.

10. Chandeliers with changeover - installation.

11. Lighting network - markings for wiring.

12. Contact panels are simple - production.

13. Insulating panels - installation.

14. Terminal boards - assembly and installation.

15. Switches and rheostats - installation in place and inclusion in the general circuit.

16. Fuses, adapter boxes, circuit breakers - assembly and installation.

17. Rubber sealing - sticker on distribution boards.

18. Simple AC and DC relays - complete assembly and regulation.

19. Three-pole switches - assembly and adjustment of switching on.

20. Contact thermocouples - assembly.

21. Microphone tubes, two-contact telephone relays, telephone sets, polarized calls, selector boxes for dispatching communications, mechanical rail pedals, Melentyev control switch locks, lightning rods, semaphore repeaters, articulated switch switches - assembly and assembly.

22. Pin pins, insulators, signal lamps, switches, toggle switches - installation.

23. Shunts - installation.

24. Brush holders - assembly.

§ 173. Electrician-electrician of the 3rd category

Description of works... Installation, assembly, testing and delivery of electrical machines of direct and alternating current with a capacity of over 50 to 100 kW, electrical appliances of medium complexity and units for them using universal devices. Assembly and installation of complex electrical appliances and electrical machines using special tools and templates. Detection during installation of damages in electrical equipment and their elimination. Installation and installation of switchboards for more than eight groups and busbar assemblies, as well as electrical equipment for cranes with a lifting capacity of up to 20 tons, welding machines with a capacity of over 300 kW and mercury rectifiers with a capacity of up to 500 kW. Binding of electrical circuits from conductors of various cross-sections and complete installation in housings. Work on switching switchboards for power electrical installations. Installation of equipment and complete switching of power stations for amperage up to 1000 A. Laying of the feeder and distribution network. Assembly and installation of complex electrical equipment and products under the guidance of a highly qualified electrician.

Must know: fundamentals of electrical engineering in the amount of work performed; device and principle of operation of DC and AC machines with a capacity of over 50 to 100 kW; ballasts of medium complexity; permissible loads during the operation of electric machines; methods of adjusting the brush mechanism of the electric motor; method of processing winding and sealing materials (impregnation, lubrication, welding, braiding, etc.); system of tolerances and landings; device and purpose of control and measuring and installation tools, special devices and equipment used in electrical installation; technical conditions for testing electrical equipment; diagrams of assembled and assembled devices, devices and electric cranes with control.

Work examples

1. Apparatuses and devices, racks for dispatching stations, stands for telephone switches - installation.

2. Mobile X-ray equipment - assembly and regulation.

3. Group switches - assembly, disassembly, high voltage current test.

4. Electric motors with power over 50 to 100 kW - installation.

5. Telephone switches with a number of up to 50 numbers, telegraph and point switches, wand devices, indicating relays, relays, group switches - completing and assembling.

6. Contactors - installation and regulation.

7. Distribution boxes - installation.

8. Complex contactor panels - installation, connection and testing.

9. Searchlights - installation.

10. Rheostats and starting controllers - installation.

11. Telephone stations for ships up to 20 numbers with all devices - complete installation.

12. Pipes - gasket.

13. Tires - manufacturing.

14. Cabinets and switchboards - installation of relays, controllers, interlocks, switches.

15. Control panels - installation.

16. Electric motors - bearing replacement.

§ 174. Electrician-electrician of the 4th category

Description of works... Installation, assembly, regulation and delivery of complex assemblies of electrical machines and electrical appliances on various machine tools and machines, as well as DC and AC electrical machines with a capacity of over 100 kW in production workshops and power plants. Measurement of power, voltage, current and resistance of wires in individual circuits and various types of connections. Identification of defects arising during the assembly, installation and testing of electrical equipment, as well as large DC and AC electric motors and their elimination. Installation and dismantling of high-voltage equipment and networks (switchgears and high-voltage electrical equipment with starting and control equipment) with voltage up to 35 kV. Cable laying in trenches, tunnels, channels and blocks on ropes, with cutting, splicing and installation of linear and end couplings and cable testing. Marking of places of installation of equipment. Complete switching of the power station with amperage over 1000 A. Equipment for oil circuit breakers. Installation of high-frequency installations with a capacity of up to 700 kW, mercury rectifiers with a capacity of over 500 kW, electrical equipment for cranes with a lifting capacity of over 20 tons and large universal metal-working machines.

Must know: design and purpose of assembled and installed complex machines, high-frequency installations, converters, power transformers and high-voltage equipment for them; technological sequence of installation of electrical equipment, assembly and installation of machines, units, apparatus and electrical appliances; the principle of operation of synchronous and asynchronous powerful machines, converters, power transformers and high-voltage equipment; substation equipment, electrical equipment for heavy-duty cranes and complex machine tools; technical conditions for the installation of machines; electrical circuits, defects arising during the assembly and installation of machines, and ways to eliminate them.

Work examples

1. Stationary X-ray machines - assembly, installation, adjustment.

2. Generators - installation according to schematic diagrams and connection of wires.

3. Multicore cables - termination of ends, continuity.

4. Telephone switches, stands for telephone switches of the Central Bank and MB, Morse telegraph sets, hitchhiking alarm relays, autoblocking - testing and adjustment.

5. Devices such as junction boxes with stamps and protective devices - binding of electrical circuits, complete electrical installation in complex panel housings.

6. Transceiver equipment of special types - installation.

7. Three-pole disconnectors - adjustment.

8. Relays of various systems - regulation.

9. Automatic telephone stations with the number of subscribers up to 1000 - installation.

10. Power transformers up to 20,000 kW - installation and testing.

11. Complex switchboards of large size - complete installation with installation and regulation of equipment and cable laying.

12. Electric motors of woodworking machines - complete assembly and disassembly, connection to the network.

13. Electric motors for locomotives, metro trains and trolleybuses - assembly and installation.

14. Crane electrical equipment - assembly and disassembly.

§ 175. Fitter-electrician of the 5th category

Description of works... Complete installation, dismantling, testing and assembly of complex high-voltage equipment for electrical substations, electrical machines and assemblies of all kinds of structures and systems, cable and overhead networks with voltage over 35 kV. Manufacturing of complex devices and mechanisms according to sketches and schematic diagrams; testing, adjustment and delivery in accordance with technical conditions. Manufacturing of the most complex template circuits and installation of real circuits from various wires. Installation of high-frequency installations with a capacity of over 700 kW. Identification of defects and damage to the network and devices and their elimination. Manufacturing of devices necessary for performing electrical work.

Must know: device, principle of operation and rules of operation of unique electrical machines and devices, converters of direct and alternating current, high-voltage equipment with voltage over 35 kV; methods of the most complex electrical wiring of mechanisms, blocks, devices, modular machines, group connections and circuits and methods of testing them; rules for testing and putting into operation machines, devices and automation; methods of measuring the values ​​of resistance and insulation.

Work examples

1. Automatic lines of metalworking machines - complete installation of electrical equipment.

2. Devices for special purposes with a very complex electrical circuit - installation and regulation.

3. Samples of transmitters multi-band and multi-stage experimental - installation according to complex schemes.

4. Equipment for powerful electrical substations - installation.

5. Electrical substations with a capacity of over 1000 kW - installation.

6. Devices consisting of several mechanisms that have independent most complex electrical wiring diagrams based on electronics, radio engineering and telemechanics - binding of a machine diagram and complete wiring.

7. Control panels and temperature control - installation.

8. Complex precision and unique machines - electrical installation.

9. Automatic telephone stations with the number of subscribers over 1000 - installation.

10. Power transformers with power over 20,000 kW - installation and testing.

§ 176. Electrical fitter of the 6th category

Description of works... Installation, complete disassembly, assembly, repair, adjustment, adjustment, testing and delivery of complex experimental electrical machines and devices, complex special non-standard equipment when combining mechanical and electrical circuits, automatic power supply and control panels for large ships, aircraft, unique and precision metalworking equipment, power plants, as well as electrical systems of automatic lines of metalworking machine tools and units for processing complex parts. Adjustment of the most complex protective and switching equipment and electrical mechanisms of unique and precision equipment. Locksmith processing of the assembled equipment, while observing the relationship between mechanical and electrical parameters. Execution of installation and docking, debugging and development work and testing of electrical remote control systems. Identification of damages and breakdowns during installation and their elimination. Checking the operating modes of the installed equipment, devices, mechanisms and installations and loading in accordance with the project of their capacity. Performing finishing work on electrical installation of ship equipment on large ships during mooring and sea trials.

Must know: design features and the principle of operation of mounted electrical machines, mechanisms of devices and complex equipment and installations on airplanes in accordance with technical specifications, and on ships - in accordance with the rules of the sea and river registers; systems of electric drives for remote control of direct and alternating current, their structure and principle of operation; mechanical transmission systems, gear and friction devices; methods of checking operating modes and loads, checking calculations and taking diagrams in the process of testing mounted electrical mechanisms, devices operating at idle and under load; methods of mounting and dismantling complex electrical mechanisms and all kinds of electrical circuits.

Secondary vocational education is required.

Work examples

1. Electrovacuum equipment (installations) with program control - complete installation with program debugging.

2. Rolling mills - installation of electrical mechanisms and electric motors, control panels, testing and delivery.

3. Metal-working machines, unique and precision - assembly, testing and commissioning of electrical mechanisms.

4. Machine tools metal-cutting with programmed control - debugging and testing.

I APPROVE:

________________________

[Job title]

________________________

________________________

[Name of company]

________________/[FULL NAME.]/

"____" ____________ 20__

JOB DESCRIPTION

Locksmith-electrician of the 3rd category

1. General Provisions

1.1. This job description defines and regulates the powers, functional and job responsibilities, rights and responsibilities of an electrician of the 3rd category [Name of the organization in the genitive case] (hereinafter - the Company).

1.2. A fitter-electrician of the 3rd category is appointed and dismissed in accordance with the procedure established by the current labor legislation by order of the head of the Company.

1.3. An electrician of the 3rd category belongs to the category of workers and reports directly to the [name of the position of the immediate supervisor in the dative case] of the Company.

1.4. The 3rd category electrician is responsible for:

  • timely and high-quality performance of tasks for their intended purpose;
  • compliance with performance and labor discipline;
  • observance of labor safety measures, maintenance of order, implementation of fire safety rules at the assigned work site (workplace).

1.5. A person with a secondary vocational education in this specialty and work experience of at least 1 year is appointed to the position of an electrical fitter of the 3rd category.

1.6. In practice, the 3rd category electrician should be guided by:

  • local acts and organizational and administrative documents of the Company;
  • internal labor regulations;
  • rules of labor protection and safety measures, ensuring industrial sanitation and fire protection;
  • instructions, orders, decisions and instructions of the immediate supervisor;
  • this job description.

1.7. A fitter-electrician of the 3rd category should know:

  • fundamentals of electrical engineering in the amount of work performed;
  • device and principle of operation of DC and AC machines with a capacity of over 50 to 100 kW;
  • ballasts of medium complexity;
  • permissible loads during the operation of electric machines;
  • methods of adjusting the brush mechanism of the electric motor;
  • method of processing winding and sealing materials (impregnation, lubrication, welding, braiding, etc.);
  • system of tolerances and landings;
  • device and purpose of control and measuring and installation tools, special devices and equipment used in electrical installation;
  • technical conditions for testing electrical equipment;
  • diagrams of assembled and assembled devices, devices and electric cranes with control.

1.8. During the temporary absence of the 3rd category electrician-electrician, his duties are assigned to [the name of the position of the deputy].

2. Job responsibilities

A fitter-electrician of the 3rd category carries out the following labor functions:

2.1. Installation, assembly, testing and delivery of electrical machines of direct and alternating current with a capacity of over 50 to 100 kW, electrical appliances of medium complexity and units for them using universal devices.

2.2. Assembly and installation of complex electrical appliances and electrical machines using special tools and templates.

2.3. Detection during installation of damages in electrical equipment and their elimination.

2.4. Installation and installation of switchboards of more than eight groups and busbar assemblies, as well as electrical equipment for cranes with a lifting capacity of up to 20 tons, welding machines with a capacity of over 300 kW and mercury rectifiers with a capacity of up to 500 kW.

2.5. Binding of electrical circuits from conductors of various cross-sections and complete installation in housings.

2.6. Work on switching switchboards for power electrical installations.

2.7. Installation of equipment and complete switching of power stations for amperage up to 1000 A.

2.8. Feeder and distribution network laying.

2.9. Assembly and installation of complex electrical equipment and products under the guidance of a highly qualified electrician.

In case of official necessity, a fitter-electrician of the 3rd category may be involved in the performance of duties overtime, in the manner prescribed by law.

3. Rights

A fitter-electrician of the 3rd category has the right:

3.1. To get acquainted with the projects of decisions of the management of the enterprise concerning its activities.

3.2. Submit proposals for improving the work related to the responsibilities provided for in this job description for the management's consideration.

3.3. Inform the immediate supervisor about all deficiencies in the production activities of the enterprise (its structural divisions) identified in the course of performing their duties and make proposals for their elimination.

3.4. To request, personally or on behalf of a direct supervisor, from the heads of the enterprise departments and specialists, information and documents necessary for the performance of their official duties.

3.5. To involve specialists from all (individual) structural divisions of the Company in solving the tasks assigned to him (if this is provided for by the provisions on structural divisions, if not - with the permission of the head of the Company).

3.6. Require the management of the enterprise to assist in the performance of their duties and rights.

4. Responsibility and performance evaluation

4.1. A fitter-electrician of the 3rd category bears administrative, disciplinary and material (and in some cases stipulated by the legislation of the Russian Federation - and criminal) responsibility for:

4.1.1. Failure to comply or improper fulfillment of the official instructions of the immediate supervisor.

4.1.2. Failure to perform or improper performance of his labor functions and the tasks assigned to him.

4.1.3. Misuse of the granted official powers, as well as their use for personal purposes.

4.1.4. Inaccurate information about the status of the work entrusted to him.

4.1.5. Failure to take measures to suppress the identified violations of safety regulations, fire safety and other rules that pose a threat to the activities of the enterprise and its employees.

4.1.6. Failure to enforce labor discipline.

4.2. Assessment of the work of an electrician of the 3rd category is carried out:

4.2.1. Immediate supervisor - regularly, in the process of the employee's daily performance of his labor functions.

4.2.2. The attestation commission of the enterprise - periodically, but at least once every two years, based on the documented results of the work for the evaluation period.

4.3. The main criterion for evaluating the work of an electrician of the 3rd category is the quality, completeness and timeliness of his performance of the tasks provided for in this instruction.

5. Working conditions

5.1. The work schedule of the 3rd category electrician is determined in accordance with the internal labor regulations established by the Company.

5.2. Due to the production necessity, the 3rd category electrician is obliged to go on business trips (including local ones).

Acquainted with the instructions __________ / ____________ / "____" _______ 20__

Similar publications